Views: 65 Author: Site Editor Publish Time: 2018-10-23 Origin: Site
The toilet partition is a crystalline plastic, light in weight, but low in high-temperature rigidity, low in brittleness, poor in environmental resistance, large in anisotropy of tensile strength of toilet partitions, easy to deform, high creep property, and not resistant to long-term loads. PA is the abbreviation of Polyamide in English, which is an important engineering plastic. Its output ranks first among the five general engineering plastics. Compared with general plastics, it has the advantages of wear resistance, toughness, heat resistance, cold resistance, corrosion resistance, and non-toxicity. It has high tensile strength and impact strength at room temperature, and it is widely used, generally up to -40 ° C - 100 ° C. Therefore, from the characteristics of the material, the toilet partition fittings made of nylon material are superior to the PP material in terms of durability.
In the case of little influence from temperature changes, even if PP construction accessories are used in the construction, it is necessary to select toilet partitioning materials with better quality. First, choose regular products. When purchasing the partition door, be sure to see if it is marked. Commodity certificate, etc. Second, the color pattern of the partition door should be consistent with the decoration style of the bathroom. For example, many consumers prefer a translucent partition door with a pattern, which is highly decorative and gives people a beautiful enjoyment; but there are also some more traditional people. Choose an Opaque Toilet Partition.
The load-bearing wall of the bathroom can't move, so can the lightweight wall be used casually? In order to change the indoor layout, it is generally permissible to demolish the light-weight wall, but it needs to be reported to the property in advance. Due to the possibility of buried water and electricity pipelines in the light wall, blind removal is very damaging.
The material of the light-weight wall is loose, and the wall of the toilet partitions is prone to cracking, especially after dismantling. Therefore, in order to minimize the probability of occurrence, it is best to carry out the lacing treatment when constructing the light body wall: 8-10 cm of steel bars are inserted into the original wall on both sides, and then the light body wall is built, which can improve the reinforcement effect and reduce the sedimentation coefficient. In addition, the cement mortar on the wall is high enough to prevent cracking. It is also effective to fill the gap between the new wall and the original wall with styrofoam.
Some owners will cut or make some grids on light-weight walls to place crafts. Will moving partitions increase the risk of cracking of light-weight walls? Hu Zengguang believes that this need not be too worried. In this case, the opening is generally not more than 30 cm, as long as the thickness of the wall is 8-10 cm. Design and cracking are not necessarily related, just pay attention to the operation of the wall, such as just a cut, the wall will appear through the crack. There is also an estimate of the overall condition of the wall before the operation. In addition, the pillow belt should be used in front of the toilet partition wall, that is, a ground foundation with a height of about 100 mm and a wall should be made by brick or concrete pouring, and the partition wall should be made on top of it, so that it can prevent moisture. Reinforce the role of new walls, otherwise, it is prone to moldy walls.
First, choose a regular product, when buying a partition door, you must see whether it is marked with a product certificate.
Second, the color pattern of the partition door should be consistent with the decoration style of the bathroom. For example, many consumers prefer a translucent partition door with a pattern, which is highly decorative and gives people a beautiful enjoyment; but there are also some more traditional people. Choose an opaque cloth partition so that others can use the bathroom while taking a bath.
Third, distinguish the material, the Partition Door is mostly tempered glass, and the quality of the tempered glass is quite different. The good-tempered glass looks carefully with a faint pattern. The skeleton of the shower room is made of aluminum alloy, and the surface is spray-treated, not rotted or rusted. The thickness of the main skeleton aluminum alloy is preferably 1.1 mm or more so that the door is not easily deformed. At the same time, pay attention to check whether the ball bearing is flexible, whether the door is easy to use and light, and whether the frame combination uses stainless steel screws.
First, the installation of the floor drain, the bathroom water flow is relatively large, it is easy to accumulate water, such as bathing, some families and washing machine